Sterling Silver Flower Ring with Tammy Jones

Wednesday, June 29, 2011

Today Tammy Jones of Jewelry Making Daily shows us how to use sawing and soldering techniques to make an adorable sterling silver flower ring. 


Tammy Jones editor Jewelry Making Daily
Tammy Jones is the
editor of Jewelry Making  Daily.

sterling silver soldered flower ring



Flowers have always been a source of joy for me. When I was growing up, one grandmother had a garden full of hydrangeas, pansies, irises, roses, and lilacs, and my other grandmother was always surrounded by flowers in her home décor and clothing. They both made quilts laden with flowers using floral fabrics, too, so it's no surprise that I've always associated flowers with comfort and happiness. Naturally, flowers are a favorite motif in my own creative projects, jewelry especially.


So when my friend and metalsmithing teacher Lexi Erickson recently told me to "cut out a shape, any shape," a flower was the obvious choice. After some sawing, filing, sanding, hammering, fluxing, soldering, polishing, and buffing, this pretty ring is the end result.


Materials:

20-gauge sterling silver sheet
8-gauge half-round sterling silver wire
small silver ball or bead for center
jeweler's saw and 4/0 saw blades
Burlife or Gemlube
flat-nose pliers and tweezers
medium tooth (#2) file
dapping block
texturing hammer(s)
torch and setup with firing brick
medium solder and pick
various sandpapers
flux and brush
pot of hot pickle and copper tongs
bowl of water

saw flower petal shapes out of sterling silver sheet
1. Draw a small, medium, and large organic shape with a fine felt-tip marker on the sterling silver sheet. Using the jeweler's saw strung with a lubricated 4/0 saw blade, cut out your petal pieces using a smooth, fluid, up-and-down sawing motion.

2. Hammer the petals to add texture, as desired. I hammered the large and small pieces, leaving the medium piece plain for contrast.

hammer petal shapes to add texture and dome in a dapping block 3. File the raw edges and finish (sand, polish, buff) the surfaces of your cutouts.

4. Dome each petal in the dapping block. Punch or hammer a small dimple in the center of the smallest petal piece to help hold the ball in place later. Pickle all three pieces for a couple of minutes to clean them; rinse and dry, being careful not to touch the backs where you'll be soldering.

5. Using sandpaper or even a kitchen scrubber, sand off the end of your solder to ensure it's clean and snip off six small pieces, about 1mm each.

flux back of petals and apply three small pieces of silver solder 6. Place the small and medium pieces next to each other face-down on the firing brick and paint the backs with flux. Use tweezers to carefully place three pieces of solder together (touching) on the back of each piece.

7. Fire up your torch with a quiet (nonhissing) reducing flame. Keeping the flame moving and with the blue cone about 1/4" from the surface, heat the brick around the pieces and slowly move in on your petal pieces, heating them gradually. Expect your flux to bubble and turn white; that tells you you're at about 400°F.

8. Heat your pieces a little more directly now, still moving the flame but staying on the piece and keeping the blue cone about 1/4" away from the surface. Don't look away; things are about to happen quickly!

flux sterling silver flower ring pieces and add silver solder 9. Watch for the flux to turn clear and glassy. That's when you know you're at 1,100°F degrees and your solder is melting and will soon flow. You'll see a bright silver line appear when the solder flows. Remove the heat immediately when you spot it. You've presoldered!

10. Lifting with tweezers or tongs (watch your fingers!), slowly tiptoe each piece into water to quench it and then drop it in the pickle for a couple of minutes. Then rinse and dry.

11. Paint the top of each piece with flux and stack face-up in the appropriate order. Sand the solder end and snip off another small piece, placing it in the dimple you created in the smallest petal piece. Hold the center bead with tweezers while you coat it with flux and then place it directly on the solder in the dimple center. Now it's time to solder again.

torch fire sterling silver flower ring pieces on firing brick 12. This is a multilayer soldering process, so it will require a little extra time. You're soldering the ball to the smallest petal, but you're also soldering the medium petal between the other two. Fire up your torch again (to a quiet, reducing flame) and move it around the stack to warm gradually.

13. Watch for the flux to bubble and turn white. Hone in at that point, keeping the blue cone of your flame about 1/4" away from the surface. Sweep back and forth across the ball in the center and move around the entire piece in a circular motion.

As the flux turns clear and glassy, focus on the center ball, watching for the silver line that indicates the flux is flowing. When you see it, aim your flame between the petals and focus on the solder you melted earlier. You can't see the silver line when that solder flows, so just allow a little extra time to be sure but keep the flame moving. Note the color of the metal; if it glows red, remove the flame immediately.

soldered sterling silver flower ring 14. Use tweezers to quench the piece slowly in water and then drop it in the pickle for a couple of minutes. Remove it with copper tongs, rinse and dry it, and test the joins. Hopefully, all the layers joined; if not, reflux and resolder until all the layers feel secure.

15. Use a slip of paper to measure your finger size and mark that length on the half-round wire. Cut off the amount you need using your jeweler's saw, not wire cutters, to achieve the appropriate shape on the cut ends. Use pliers to curl the wire into a partial ring shape and test fit it on your finger or ring mandrel.
sterling silver flower ring wire
16. Because the back of the ring is domed from the dapping, careful filing will be required to get angled ends that will fit the curved back of the flower pieces snugly. Place the flower piece face-down on the firing brick and test the ring until it can stand upright on its own on the back of the ring.
flux and torch solder sterling silver flower ring
17. When the ends are filed correctly, sand the end of your solder and snip off two more small 1mm pieces. Paint the back of the flower and the ring wire in flux.

18. Place a piece of solder on the flower where each end of the ring wire touches it and solder in place using the same gradual technique as for the previous pieces.
silver solder melt and flow on sterling silver flower ring
19. Warm the ring wire separately (until the flux melts) before using tweezers to move it onto the flower piece. Watch for the flux to bubble and turn white, then clear and glassy, and then for the shiny silver line when the solder flows. Quench slowly with tweezers, pickle, and voila!

You can see that my ring is a whitish matte silver. The prolonged heat required to complete the multilayer soldering burned off some of the metals alloyed in the sterling silver sheet, resulting in an exterior layer of fine (pure) silver. I liked the look of it, so I left it that way. You can, too, or you can polish yours to a high shine, give it some color with liver of sulfur, or apply any patina you prefer.


Sawing, hammering, soldering--it sounds like fun, doesn't it? It was, and I'm anxious to fire up my torch again. Fortunately there are lots of projects with intermediate and advanced techniques like these in the newest series of Beads, Baubles and Jewels. The latest season's segments are full of expert tips and tricks for wire and metalsmithing projects, including techniques such as wire wrapping, resin, pen plating, cold connections, chain maille, and soldering, of course!


Thanks, Tammy!  You can learn more about metalsmithing by visiting Beads, Baubles and Jewels or checking out my book picks below!

15 comments:

Jo said...

A fantastic detailed tutorial, thank you! I'll be referring my students to it!

Tammy Jones said...

Thanks for sharing, Lori! And thanks for your comment, Jo, I'm glad you like it. I loved making (and still love wearing) this ring! I hope this project is of use to your students.

Tammy Jones
Editor, JewelryMakingDaily.com

Crystal Choker Necklaces said...

Good one. Just referred to my kids, lets see what happens :D

Anonymous said...

I drop a leave a response each time I like a article on a site
or I have something to contribute to the conversation.

It is a result of the passion communicated in the article I read.
And after this article "Sterling Silver Flower Ring with Tammy Jones".
I was moved enough to leave a comment :-P I do have a few questions for
you if you usually do not mind. Is it just me or does it look like some of
the remarks look as if they are coming from brain dead
visitors? :-P And, if you are writing on additional
online sites, I would like to keep up with you. Could you list the complete urls
of your public sites like your Facebook page, twitter feed,
or linkedin profile?

Look at my homepage - akribos xxiv watches for women

Anonymous said...

Great weblog right here! Also your web site rather a lot
up fast! What web host are you the use of? Can I am getting your affiliate hyperlink
to your host? I desire my site loaded up as quickly as yours lol

Take a look at my weblog: www.wikibegin.org

Anonymous said...

Appreciate the recommendation. Let me try it out.

Look into my webpage home business

Anonymous said...

I'm curious to find out what blog system you are utilizing? I'm experiencing some small security issues with my latest
blog and I would like to find something more
safeguarded. Do you have any recommendations?



My blog post - wiki.kombinasi.net

Anonymous said...

Hello to all, how is all, I think every one is getting more from this web site, and your views are nice for new users.



Also visit my web site; akribos watches for women

Anonymous said...

I don't know whether it's just me or if everybody else experiencing issues
with your site. It looks like some of the written text in
your posts are running off the screen. Can someone else please provide
feedback and let me know if this is happening to them too?

This may be a problem with my web browser because I've had this happen previously. Kudos

Feel free to visit my web page: affiliate marketing network

Anonymous said...

I think this is one of the most vital information for
me. And i'm glad reading your article. But wanna remark on few general things, The website style is perfect, the articles is really nice : D. Good job, cheers

Also visit my page: http://www.wikifredensborg.dk/index.php?title=Brugerdiskussion:OIYPaige

Anonymous said...

I've been surfing online more than 4 hours today, yet I never found any interesting article like yours. It's pretty worth enough for
me. In my opinion, if all website owners and bloggers made good content as you did, the internet will be much more useful than ever before.



Look into my site - seo services usa

Anonymous said...

Hey there! Would you mind if I share your blog with my twitter group?
There's a lot of folks that I think would really enjoy your content. Please let me know. Thanks

my web blog; affiliate marketing

Anonymous said...

you are in point of fact a just right webmaster. The website loading velocity is amazing.

It sort of feels that you're doing any unique trick. In addition, The contents are masterpiece. you have performed a fantastic job on this matter!

My web-site www.nihonlinks.com

Anonymous said...

you're actually a just right webmaster. The website loading velocity is incredible. It seems that you are doing any distinctive trick. Moreover, The contents are masterpiece. you've performed a great activity in this subject!


my webpage :: nexus.thewebstore1.com

Anonymous said...

Having read this I believed it was really enlightening. I appreciate you taking the time and effort to put this
content together. I once again find myself spending way too much time both reading and commenting.
But so what, it was still worth it!

Stop by my web-site ... jordan carmelo

Post a Comment

Thanks so much for commenting! It always makes my day!